This VPN protocol usually uses a private key (client) / public key (server) combo that is used to connect through a public IP address (the 2 nodes can’t communicate it without) using the specified TCP or UDP (more often lately) and port to create the VPN tunnel that’s gets established during the handshakes.

There is a whole lot more going on with the process but that’s a high level view. But I have a WireGuard VPN service running on a raspberry pi that I put in a DMZ on my perimeter firewall.

But a port scanner would be able to see that port is open. Make sure you keep your software up to date. Hopefully the software devs of the VPN application is keeping their stuff up to date to avoid any vulnerabilities getting exposed in the code and a backdoor getting created because of it. As long as that doesn’t become an issue, no one will be able to get through without the private key. And those are usually uncrackable in a lifetime with the complexity and length of the key.

Glad I could help! 😃

Ok, I grabbed a few screen shots for you as well. Here is a site that will link you to MEBx setup that enables AMT: http://h10032.www1.hp.com/ctg/Manual/c03883429

When power on your ProDesk G3, you can access the MEBx setup by pressing Ctrl+P or they also say F6 or Escape will get you there. Intel AMT runs on a different IP address than what your OS gets. You can assign DHCP or a static IP address and setup your admin password. You can then access the portal from http://ipaddress:16992 There should be a method of access what would show on the screen through a KVM like access but I use MeshCentral for that so I couldn’t tell you how to do it without.

Hopefully, that gives you a start. Feel free to reach back out if you have any questions. Thank you!

I’m not in front of my computer atm, but I think I have something that can help you out. I have a 3-node Lenovo Thin client cluster that I manage their KVMs using the Intel vPro. I even went a step further using MeshCentral running on a VM to centralize my KVM access since I have 3 of them, but that’s another story.

Anyway, I’ll see if I can grab you some URLs in the morning if someone else doesn’t beat me to it or you find it on your own running google queries.

2024 - Mexicans at the border (you know it’s already happening)

3-Node ESXi cluster with 10 Debian VMs, 3 Windows VMs, and one FreeBSD VM

Examples: ServiceNow, Connectwise, Jira Service Desk

Look into getting a CMDB and keep track of all of your hardware. That can store the hostname / IPs of your KVM / OS or virtualization layer, vkernels, storage adapter IPs, your vCenters and so on and so forth. If your data is getting so big that spreadsheets are getting tough to manage, then you probable need a more enterprise method of storing it.

I couldn’t see it the wrong way at all until I really stared at it. Then once I saw it, I couldn’t unsee it. lol

deleted by creator

They call it a tcpdump but Wireshark analyzes all network traffic. You can use the udp.port == 51820

Do you have a laptop? Probably more tools and easier to test from there.

Meant to say if you still get stuck, run Wireshark on your FW and your VPS and run a tcp dump and filter the traffic to see where the data stops.

You can also use traceroute to your public IP on the port 51820 and check your connectivity or even curl: -v http:////publicip:51820

Did you setup a NAT on the firewall? You have to setup a static NAT on the interface that your Public IP sits on and to the private IP address of your VPS (you are using a private network space from one of the other interfaces on your FW right?).

Make sure that the policy that you create with the NAT includes UDP 51820 (unless you changed the default port) People often mistake using TCP which is a different protocol. If that doesn’t work, then look at the traffic on your FW